spritzer Posted March 19, 2013 Report Posted March 19, 2013 Tube input makes no sense as it gives us no benefits. That's the whole issue with most hybrid amps, most of them were designed with a SS front end but then tubes were added after the fact by somebody else.
Valentin Hogea Posted March 19, 2013 Report Posted March 19, 2013 So I just got some old 1982-made Toshiba 2SA1145Y and 2SC2705Y. And now I'm looking at my Mouser-ordered 2SA1145-O. nd I was thinking. Wait, what's the difference except being 25 years newer. Well that O and Y. hFE classification O: 80 to 160, Y: 120 to 240 And after reading that in the data sheet. I still can't fathom, which is "best"? Neither? Or should Y's be used with Y's and O's with O's etc? orry, very new to the whole transistors-thingie. Cheers, V
Pars Posted March 19, 2013 Report Posted March 19, 2013 You may find some overlap in hFE when you test them between grades. Or not. If matching, I you can see what matches up and use those. No difference in the parts, just graded during testing by the manufacturer.
kevin gilmore Posted March 20, 2013 Report Posted March 20, 2013 well I had nothing to do for an hour today http://gilmore.chem.northwestern.edu/dynahipower6.jpg
livewire Posted March 21, 2013 Report Posted March 21, 2013 (edited) Ok, I'll bite, Tho i'ma not building a dynahi. What is with the superimposed LT1021 and the LM4040 ? One on each side of the pcb? Also the "blacked-out" psu 'lytics. Are they placed on opposite sides of the pcb, or just use extra insulation over the solder-resist, or ? Please excuse the seriously stupid questions, just curious... Edited March 21, 2013 by livewire
Victor Chew Posted March 21, 2013 Report Posted March 21, 2013 (edited) Slightly more parts than the original (ie. addition of 24v zener, ik resistors etc). I assume better current regulation. The 40 kdt has also been corrected to 20kdt. Previously missing 1k resistor has also been added. I believe this makes checking, for those of us that have built the older version, easier with comparison against this updated version. Thanks Kevin. Edited March 21, 2013 by Victor Chew
Lil Knight Posted March 21, 2013 Report Posted March 21, 2013 Ok, I'll bite, Tho i'ma not building a dynahi. What is with the superimposed LT1021 and the LM4040 ? One on each side of the pcb? Also the "blacked-out" psu 'lytics. Are they placed on opposite sides of the pcb, or just use extra insulation over the solder-resist, or ? Please excuse the seriously stupid questions, just curious... 1. Use either of them. 2. Take a look at the revised KGSSHV psu.
jwzhan Posted March 21, 2013 Report Posted March 21, 2013 (edited) black out is to prevent arcing via the cap metal casing.. more relevant to HV... Kevin, is it possible for you enlarge the holes for 2pF and 0.47uF (on the amp board) a little? I just got some 0.47uF wima caps, and again the leads don't fit... I didn't want to look for replacement, so I'm just shaving the leads to make them fit... Lead diameter for the wima is 0.8mm Edited March 21, 2013 by jwzhan
livewire Posted March 21, 2013 Report Posted March 21, 2013 black out is to prevent arcing via the cap metal casing.. more relevant to HV... Thanks for the reply. Is this an extra coating on the pcb? Or maybe an applied kapton tape or other insulator? Please educate me.
Victor Chew Posted March 21, 2013 Report Posted March 21, 2013 (edited) As far as I understand, this is to avoid the possibility of ground plane shorting the cap. For some reason arcing occured between the two in jwzhan KGSShv build blowing a hole in the circuit board. Could have been caused by cracked cap covering which cut through the solder resist resulting in arcing. Its rare but did happen to jwzhan. Edited March 21, 2013 by Victor Chew
kevin gilmore Posted March 21, 2013 Report Posted March 21, 2013 (edited) The black area is where there is no groundplane. So if there is going to be an arc, it has to go thru the board to the other side. The thickness of the board is good for a few kilovolts. I'm sure its not necessary at 30v, but its trivial to do. I will increase the size of the cap holes on the amp board. As far as the voltage references, the linear tech part is a fair amount more expensive than the ti part. You use one or the other, not both. Edited March 21, 2013 by kevin gilmore
livewire Posted March 21, 2013 Report Posted March 21, 2013 Thanks for the clarification Lil Knight and KG.
kevin gilmore Posted March 21, 2013 Report Posted March 21, 2013 Kevin, is it possible for you enlarge the holes for 2pF and 0.47uF (on the amp board) a little? made the holes .040 inch, they were .030 inch enough?
Kerry Posted March 22, 2013 Report Posted March 22, 2013 Very nice on the PS Kevin. I was just looking at this and was wonder if the voltage reference was floating. I thought it should tie to ground but didn't see it.
kevin gilmore Posted March 22, 2013 Report Posted March 22, 2013 both are tied to ground at the bottom of the 6k resistor. thermal hard to see.
Currawong Posted March 25, 2013 Report Posted March 25, 2013 Things are looking up for me being able to actually build something here without family chaos interfering so I want to ask, given the issue with the sand, should I simply wait for the new boards first?
kevin gilmore Posted March 25, 2013 Report Posted March 25, 2013 if you already have the old boards and a way to do the off board heatsinks, then you should do it, you should have very little trouble getting the parts there. Otherwise the new boards are going to be a fair amount easier to build.
preproman Posted March 26, 2013 Report Posted March 26, 2013 Now that I got my hands on a GS-X mk2 . What will be the major differences between the GS-X mk2 and the on board SuSy Dynahi?
kevin gilmore Posted March 26, 2013 Report Posted March 26, 2013 gsx-mk2 will do 80 volts peak to peak balanced with a balanced input only dynahi will do 120 volts peak to peak balanced gsx is about 8 watts class A per balanced channel dynahi is about 30 watts class A per balanced channel dynahi drives speakers if you want it to. gsx-mk2 will NOT drive HE6 to ear bleeding levels dynahi WILL
preproman Posted March 26, 2013 Report Posted March 26, 2013 Oh yeah.. That's what I'm talking about. Thanks...
Voltron Posted March 26, 2013 Report Posted March 26, 2013 Wait a minute. ^^This fucking guy isn't blubliss so what is he doing with this avatar?!
livewire Posted March 26, 2013 Report Posted March 26, 2013 He has been using it at the other place for quite sometime. BB has a dog's head o'er there.
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now