naamanf

Felder Format Dual 51. Skip the BS. If you must https://www.rockler.com/powermatic-8-parallelogram-jointer?country=US&sid=V91040&promo=shopping&utm_source=google&utm_medium=cpc&utm_term=&utm_content=&utm_campaign=PL&gclid=EAIaIQobChMIgMvfkNDV9QIVoRvUAR0vsQ7_EAQYCyABEgI_gPD_BwE

Put it on the stand. It cuts wood.

Probably in 2023 when it’s finished.

Kapex arrived. So far I’m loving it. Makes a great resting location when taking a break during my shop rearranging.

The drawer box is built to be made into one piece with a dado on all for sides for the bottom to fit into. Then the drawer front is secured from the rear with wood screws.

Not for these vet student slum houses. I will keep that in mind for more important projects though.

Oil based paint is whatever I can find around here. Hit or miss mix off PPG and Benjamin Moore. Sherwin Williams has been a dry hole for a while. I would assume any place that supplies cabinet shops has HDF. Rare to find at box stores.

Al is correct. Raised panel HDF single piece doors are pretty common for painted cabinets. There are CNC bits to match just about every shaper knife profile.

One piece HDF from the ping pong table.

What? I’m guessing you are asking how the drawers and doors are attached? It’s a face frame cabinet

I find that hard to believe, have you measured the voltage of when the saw kicks on? Just because it’s a 15a circuit, doesn’t mean it can only carry 15.

Curious how they compare to the Ridge Carbide blades. I’ve been meaning to get one or the other to replace my Freud. I really liked it when I had my Jet, but now it just seems to do a okay job at best.

There is always a ass before u.

I can only assume you have taken up angling.

Okay, I see it meow. Tenching feature? Does it do moats as well?

How are you attaching the the two sides of the gate where the 1/8" gate is? Decided I need to do some more meta woodworking and build a proper miter saw station. Going to clean off some space, remove some built in shelves, and build a station. How are you liking your setup so far, Al? Also need to decide if I just roll if my old Hitachi saw (which has been a work horse and pretty solid over the years) or move to something hopefully better.

Second vanity complete. Definitely going with a larger reveal for the kitchen I’m going to do next.

Good to know the rest is the line is also good. The Blums are impossible to get here and online, why I’m looking for the best alternatives.

I’ll have to check them out, hopefully there is a local supplier. Picked up these Amazon Basics Euro handles for the cabinets. The quality is surprisingly good. Solid stainless with quality look and feel. Best part was they were $1.15. Which is probably bad since I’m just supporting the Bezos and China.

I also use the Blum hinges, impossible To get it perfect without some tweaks. Really wish the Blum slides were in stock, the cheap knockoffs make it much harder to do. The ping pong cuts everything minus the face frame rails and stiles. Kind of wish I had an edge bander now 😂

Pocket screws for the face frame. Dominos don’t really make sense and would be more work. The rest was dados, glue, and brad nails. Board is looking great!

Going in one of the two smaller houses we bought recently. I have another vanity all cut, just need to put it together. I think getting the faces on take up about half of the construction time. Getting it all lined up is definitely a chore, I have a fully kitchen to do next, think I’m going to go with a larger reveal so being perfect isn’t so critical.

Put together a vanity.

I am. Using iVac. I have a metal pro one and plastic one. So far no issues other than the power supplies they supplied were AC/DC and would keep on frying from static. Turns out there is already a DC power supply already built into them. Switched to just using transformers and I haven’t had any issues.