fishski13

Ben's Cycle is having a %15 off holiday sale. decided it was time to get ride of the sagging stock Wabi saddle and picked up a San Marco Rolls: https://www.benscycle.com/p-3557-san-marco-rolls-miele-saddle-tan-steel-rail.aspx . i'm buying blind but both the Rolls and Regal seem to be universally liked by most asses.

strapped on a new pair of Voler bibs for a 1hr on the rollers today. my longest ride this summer was only 50mi and my butt felt reasonably fine in the saddle. with a single speed you're going to spend more time out of the saddle in general to attack the hills, but with rollers i spend much more time in the saddle and needed a pair of padded cycling shorts. i can ride out of the saddle for short periods but it still feels a bit sketchy. getting proficient on rollers takes some time. learning to ride one handed or even turn your head to the side without ending rubber up takes practice. i wish i could find the youtube video of a guy snorting rails of coke while playing tennis on a Nintendo Wii. with a googled 15% off promo code these Voler bibs came in at just over $75, just enough to qualify for free shipping: http://voler.com/browse/product/li/1110521 . the fit is true. stitching and construction is excellent.

i just discovered this great thread. lots of helpful info for someone like myself just getting back into bicycling. i picked up a Wabi Classic for my b-day last July. steel frame and cuts the pavement like butter at 110psi. a flip-flop hub, riding SS, and 46/16t gear. the only components i want to replace are the tires, seat post and ass hatchet. a cadence meter would be swell as well. i've put 500+mi on it plus a few hours a week on the rollers. i don't have much climbing on the local roads/trails here in my suburban enclave. i have access literally in my back yard to the huge Elm Creek paved trail system here in Maple Grove, MN. round trip to my favorite bar is only 10mi. after numerous adjustments, i think the fit is comfortable. the only thing i need to work out are my shoes and cleat positioning. i initially bought my Giro Privateers one size too small. thankfully REI was cool enough to allow me to exchange them (i know many members abuse their generous return policy). my feet are not equal in size and i've been playing around with various sole inserts and sock combos. going for a ride clears the mind of all the day to day bullshit. i feel like a kid again.

match NPN to NPN and PNP to PNP per board. i was able to basically get identical matches with the MPSW06/56 for each board. i bought 100 pieces each since they're cheap. i think 1-2% variance in hfe would be fine. for the MJE15030/31, within 5% is good. i would recommend buying 2x more than you need. if you don't match the sand, you could have significant differences in bias across each of the devices. you need to measure across each and every one of the 20R resistor pairs to make sure all of the output devices are biased reasonably close to one another. you don't want one biased at 50mA and another cooking at 90mA. in my chassis, i was able to get the bias to 42-43mA per output device with a reasonable junction temp.

G600, you need to match the transistors. i would just rip out all the sand and make the effort to match them. in my mancave, the on-board heat sinks will do 50mA/500mV per output device, measured across each paralleled 20R pairs, in free air... if you want a safe junction temp - thats around 3W dissipation per 2.5" tall heat sink with BJTs that have positive temp-co properties. depending on chassis ventilation, you may have to go lower.

i realized that but went ahead and posted it anyway since other builders may have the same biasing questions. as to your biasing issues, i have no answers other than you possibly have poorly matched devices or fakes. i would try to re-bias.

biasing the SuSy boards: -before first power up, the pots that flank the THAT340 should be at their mid point. the outer biasing pots should be as follows, when looking at the board with the heat sinks at the rear: L - fully CCW and R - fully CW. leave the DC servo opamp out. -bring up the bias by turning the L outer biasing pot CW and the R CCW, keeping tabs on the DC offset. both pots will increase the quiescent current bias, but also affect the amount of DC offset. i just turn them in equal amounts until i hit my target quiescent current and then tweak for lowest DC offset. the offset will fluctuate quite a bit, like 100mV. small fractions of turns on the pots will cause the off set to jump. be patient. i think the best i could do was roughly +70mV to -30mV. -insert the DC servo. measure the offset between the O(+) and O(-) - i measured 20 and 25mV. turn one of the THAT340 pots CW and the other CCW, 1/2 turn each. note if the DC offset went up or down. if it went down, then continue turning the pots in the same manner, in 1/2 turn increments, until you reach 0mV. if the offset went up, then reverse the turns in the opposite directions. -i was able to get less than 0.5mV offset and very stable. on cold start up, still a very low 2mV. zero pops or hiccups through my HPs either on power up or power down.

mucho gracias!

congrats. enjoy.

most awesomest translation.

agreed. can drive drive any sensible HP without issue and sounds fantasic. don't skimp on pot/SA. silly cheap and an amp that sounds good with every thing.

thanks! TXs are inductive:) the Bulgin latching power switches i use are rated only for 3A. i wire in a 10A mechanical relay to take the brunt of the inrush current. the only SSRs i've seen are spendy too.

i'm not SSR savy - only seen one in a B3 DAC repair i performed. what's your primary beef?

Marc, copy and paste. Notes about R34 and R35: The default value for these resistors is 0.47Ω. If you have TRS headphone output jacks, the value may be increased to 1&Omega to 2.2Ω for added protection. This is because TRS plugs create momentary short circuits while being inserted or removed, and could potentially damage the output MOSFETs. On 4-channel balanced configurations with only XLR output jacks, or if the amplifier is for speaker use only, it is not necessary to increase the value of these resistors. The drawback of increasing these resistors' value is a small loss of maximum output voltage swing capability. If you use the default 0.47Ω value with TRS jacks, it is recommended that you turn off the amplifier before inserting/removing the headphones plug. Or, at the very least, turn the volume to minimum and insert/remove the headphone plug very quickly. Metal oxide resistors are the only recommended resistor type for R34 and R35. In particular, do not use wirewound types. Also, do not use resistors rated higher than 2W.

i've never had an issue with my B22 in 5 years, even with 0.47R Source resistors. i think most builders are opting to increase the resistance to 1-2.2R to provide a larger margin of safety against shorts.