Leaderboard

Moving day! New furnitature looks amazing in the new place. Hat tip to @Hopstretch who sold me his family’s old dining room set. My old apartment was too small for a dining room table so I’ve been eating meals at home on the couch or at my desk for years. Now I get to eat at a table like an adult. Feels good, man!

Really does fit your room well. Hope the floor is sturdy, because that stuff is heavy! @TMoney threw in some very kind (and tasty) sweeteners and I immediately reinvested the entire proceeds in new audio gear, as is traditional.

Drunk people are allowed to use any thread to post in for the "Drunk Thread". It makes for a more interesting read the next day.

So I have not posted here in so long: I have not been drinking much? I have been drinking so much that I cannot even post in the morning? hmmmm

Not the greatest pics, but here is the router table Steve and I built, with the horizontal and mortising setups shown below

casually I've been listening to Brad Mehldau's recent release of "After Bach"

The link above actually loads a page which says: Rare steak 'is safe to eat' Meat can become contaminated during the butchery process Eating rare steak will not cause food poisoning if kitchen utensils used to cook it are kept clean, it is claimed. University of Nottingham scientists spiked steak samples with E.coli bacteria, then cooked them rare. The bacteria only survived where the steaks were touched by utensils that were not cleaned after being used to handle raw meat, researchers found. The study dispels the myth that eating rare steak is in itself unsafe, the Meat and Livestock Commission said.

Nice rework station! The price is pretty reasonable too, should have known about it six months back (when i bought my rework station). Any recommendation on desolder gun? Hakko fr300/301 any good?

I laughed, I cried.

This! Win win!

Congrat TMoney! I like the angles of the ceiling, especially into the hall where it keeps the angles....

Down a hill.

Looks great Adam!

Dungen - ta det lugnt 2016 vinyl repress. All analog pressing! Sounds killer. Bought the CD when it first came out and while the music was great the sound was pretty compressed (vinyl was cut from CD master). This repress is super punchy and dynamic without being harsh.

Brad Mehldau trio "ODE"

^^ this... ... and Glencairn's (lots of Glencairn's) -- They are not the best glass that I have ever tried - but they are probably the best overall balance of nose (mine fits mostly in the glass) - palate delivery (whisky makes it in my mouth, most of the time) - and durability (I have had them bounce off concrete floor and I grabbed it out of the air on the up travel). ... and they are everywhere - one of the main reasons that I use them is consistency - if I go to a tasting or event - they have them too - so at least the glass is the same for all whisky. cheers

Built this last weekend. Peopoly Moai SLA 3D printer kit. Build took about 4.5 hours, pretty straight forward and well thought out design. For those not familiar, SLA style 3d printers are quite different from regular FDM 3d printers. Where FDM melts and extrudes plastic layer by layer to build a model, SLA uses a light source to cure a UV sensitive plastic resin layer by layer. The resin sits in a small reservoir, a metal built plate presses down to the bottom, and the light source cures a given layer. The reservoir then peels itself off the cured resin, the metal plate dips back into the liquid resin one step higher, and the next layer is cured from the light below. Repeat over and over until your model is fulled 'pulled out' of the rub. The two typical methods of SLA printing are dubbed 'SLA' which uses a laser and galvanometers to trace each layers' design, and 'DLP' which uses a DLP or LED screen to project the stencil of an entire layer. Advantage of SLA type is that it's a bit more precise/detailed, advantage of 'DLP' type is that it's cheaper and can cure an entire layer at once so it can be faster for larger models. SLA resolution is limited to the size of the laser beam, DLP resolution is limited to the pixel size but is jagged in comparison. As LED screens improve in resolution and get cheaper, I expect DLP to become more popular in the future. SLA can be kinda messy, smelly, and is slower and considerably more costly than FDM 3d printing. The resins right now also aren't that great mechanically - they're pretty brittle. The advantage they have is that they're WAY more precise than FDM printers. For this reason, they're used a lot by the dental, jewelry, and miniatures industries. I already have an FDM printer that serves me well for rough prototyping, but this printer should be much more useful for creating production level short run molds. I've wanted this ability for a while now but these machines are typically $4-10k+ all in, so this kit for a fraction of the price (~$1300) is a great deal. Those interested in something similar but even cheaper (~$500) might want to check out the Wanhao D7 or Anycubic Photon, both DLP type machines, but you have to be willing to tweak things a bit more. Anyways, enough rambling. Onto some build pics! Kit came in a big ol' box. Very well packaged. Some of the electronics and the two galvanometers. The laser shoots into those two little mirrors, which direct the laser up to the build area and control the X and Y positions for tracing out each layer. All put together. Liquid resin stays in that clear vat, aluminum build plate dips into it from above to control Z position and holds the model. Gotta keep the door closed so UV light doesn't start curing the resin. In action! It looks really cool in person. One thing I love is how quiet it is during operation - no problems letting this run overnight. The laser is coming in from below. Post processing the final part. This is just a little test ring to make sure things are working to spec and the build went as planned. Agitate it in IPA for a while to get rid of any excess resin, agitate in water to rinse off. Repeat a few times and then put in the sun or under a UV light for a while to fully harden. I might get an ultrasonic cleaner later for this step since I'm inpatient. Haven't printed anything terribly exciting yet, mainly just small calibration models to get dimensional accuracy locked in. I'll post something more interesting later.

learn the art of the bottle lip. no glasses nor shirts required.

"In Soviet Russia headphones listen to you!"

Know there's a wide spectrum of opinion around here on the gun issue, so please don't take this as an attack -- but this made me laugh.